Are you ready to give the competition a Whup'N? Well now you finally can, and you can only get this ball at bowlingball.com. With the introduction of the Hammer No Mercy Whup 'N, Hammer is Proud to offer a unique twist to the HART core concept that provides more aggressive backend attack for right-handed bowlers. Developed by our team of design engineers, the HART Offset core changes the orientation of the pin, HART, and center of gravity locations on the ball in order to produce length and aggressive backend reaction for right-handed bowlers without the need for exotic layouts and weight holes. Unfortunately, the No Mercy Whup 'N will not provide the same length with aggressive backend reaction for left-handed bowlers or bowlers with full-roller ball tracks. The HART Offset core concept allows for more length and more aggressive backend reaction by placing the pin at 4 1/2 - 5 1/2" from the PAP (Positive Axis Point) and the HART well into the ball track. This ball is designed for Right-Handers Only!!
|
Featuring the HART core concept and new Violent Hook Reactive coverstock, the No Mercy Beat'n provides the most aggressive ball motion in the Hammer product line. With more length and more aggressive backend reaction than the original No Mercy, the Beat'n is going to cause the competition to beg for Mercy.
|
|||||||||||||||
|
|
| Line | No Mercy |
|---|---|
| Color | Black/Blue Pearl |
| Coverstock | Reactive Pearl |
| Core | 2-piece Asymmetrical |
| RG | |
| Differential | |
| Intermediate Diff | n/a |
| Factory finish | Polished |
| Weights | |
Illustrations shown are for Right-Handed Bowlers. Please reverse for Left-Handed Bowlers.
Do no use traditional mass bias layouts for the Hammer No Mercy!!!
Hammer Aggressive Reaction Technology (HART)
Hammer is very please to offer the unique Hammer Aggressive Reaction Technology (HART) core concept to the bowling industry. Developed by our team of design engineers, this radical new concept in bowling ball core design provides maximum performance without the need for exotic layouts and weight holes. It is that simple.
The HART core concept allows for strong hook motion with aggressive backend by placing the pin at 4�? - 5�?��� from the positive axis point and the HART in or near the ball track, The No Mercy offers a simple approach to asymmetrical cores so you do not have to over think this one. For aggressive ball motion, drill No Mercy series balls with Drilling #1 and have a nice day.
Tuning Ball Motion:
The coverstocks used on the Hammer No Mercy series will provide aggressive hook motion. However, it is important to keep in mind that all bowlers have different needs. The No Mercy coverstock can easily be sanded to a rougher grit for stronger hook motion in oil or polished for more length, more aggressive breakpoint and less total hook. Please consult your pro shop operator for additional assistance in tuning ball motion.
Ball Care:
It is imperative to maintain your new Hammer No Mercy by cleaning the coverstock immediately after each bowling session using bowling ball cleaning products designed for reactive balls. Hammer highly recommends Powerhouse energizer ball cleaner applied with a micro-fiber towel to remove the dirt and oil from the surface of the ball.
Drilling #1 - Most Aggressive
Ball Motion: Length with aggressive backend
Lane Condition: Medium to Heavy Oil
Flare Potential: High (5���+)
Pin Placement: Place pin at 4�? - 5�?��� from the positive axis point (PAP)
HART Placement: Place HART in or near the ball track keeping side weight and finger/thumb weight to less than 1 ounce
NOTE: For bowlers with higher rev rates, place the pin at 5 - 5�?��� from the bowler���s positive axis point. For bowlers with lower rev rates, place the pin at 3�? - 4��� from the positive axis point.
Drilling #2 - Strong Arc
Ball Motion: Strong arcing hook (about 2-4 boards less than Drilling #1)
Lane Condition: Medium Oil
Flare Potential: Medium (3-5���)
Pin Placement: Place pin at 4 - 5��� from the positive axis point (PAP)
HART Placement: Place HART 2��� right of the ball track
Balance Hole: If needed, place balance hole at 4��� from the center of span on a line through the center of gravity.
Drilling #3 - Controlled Arc
Ball Motion: Controlled arc (about 4-6 boards less than Drilling #1)
Lane Condition: Light to Medium Oil
Flare Potential: Medium (2-4���)
Pin Placement: Place pin at 5 - 5�?��� from the positive axis point (PAP)
HART Placement: Place HART 1��� right of the ball track keeping the side weight and finger/thumb weight to less than 1 ounce
Drilling #4 - Length with Smooth Arc
Ball Motion: Excellent length with smooth arc (about 6-8 boards less than Drilling #1)
Lane Condition: Light Oil
Flare Potential: Low (0-2���)
Pin Placement: Place pin at 5 - 5�?��� from the positive axis point (PAP)
HART Placement: Place HART 3��� right of the ball track
Balance Hole: If needed, place balance hole at 4��� from the center of span on a line through the center of gravity.
Drilling #5 - Full-Roller Layout
Full-Roller Ball Track Only!
Ball Motion: Strong arc
Lane Condition: Medium to Heavy Oil
Flare Potential: High
Pin Placement: Place pin at 4�?��� from the center of the span and 2��� from the grip centerline
HART Placement: Place HART at 4��� from the grip centerline
Balance Hole: If needed, place weight hole at approximately 5��� from the grip center on a line connecting the grip center and center of gravity.
Do not use traditional mass bias layouts for the Hammer No Mercy!!!
